How to maintain air compressors? What should we pay attention to when operating air compressors? Here let Chengdu Pudding Mechatronic Co. (CPMC) provide the advices on air compressors maintenance and instructions on how to operate the system.
1. Replace the air filter;
2. Replace the oil filter;
3. Replace the oil and gas separator;
4. Replace lubricating oil;
Specific Air Compressors Operation Methods
The following operations must be performed only when the power is turned off and there is no pressure in the machine)
Remove the screw at the end of the air filter cover, remove the tail of the cover, remove the air filter locking screw, take out the air filter, install the new filter, and reinstall the filter and cover in the reverse steps.
Use a special tool to lock the bottom of the filter and turn it forward to unscrew the filter. Use a clean cloth to clean the bottom of the filter and apply a little oil. Apply a little oil to the seal ring of the new oil filter and install the new filter. And lock it with special tools.
The method is the same as replacing the oil filter.
When the oil temperature is between 30 and 60℃, the viscosity will decrease and it will not burn your hands. At the same time, it will drain the residual oil of the unit. Therefore, if the oil is cold when changing the oil, first turn it on and run it for 2-3 minutes. When changing the oil, make sure that the unit is pressure-free before proceeding. First, disassemble the oil filling nut of the oil-gas separation barrel and prepare the residual oil with a suitable container. Open the oil drain valve under the barrel, and turn the head pulley by hand from time to time to drain the oil stored in the head.
After the oil is completely drained, close the drain valve. Inject new lubricating oil, and turn the head pulley by hand from time to time to facilitate the suction of oil into the pipe and the machine head. After immersing the oil level mirror, the oil fills 2~3cm (this is an empirical value, the actual oil level needs to be observed when the machine is turned on and loaded). After filling the oil, install and lock the oil nut, and remove the air intake Valve, inject a small amount of lubricating oil from the air inlet of the machine head, and the amount of oil is only two-thirds of the submerged rotor. Install the air inlet valve. Clean the surface of all parts of Henan air compressor.
Three, test machine
After power-on, directly start the air compressor, listen to whether there is any abnormal noise, observe whether there is oil leakage, and see whether the oil level is appropriate (the oil level should be observed during loading, and the position should be 1/ of the oil level mirror. 2~2/3) Otherwise, put more and less make up. After confirming that there is no abnormality, install the side panel and the rear side panel, and you are done.
Air Compressors Trade Service is online distributor for air compressors and compressed air products in Chengdu, southwest China. Not like most machinery distributors, our mission is not to sell as many air compressors or spare parts as we can. Our philosophy is to partner with more and more clients to help them salvage net profit by lowering their import cost. As is known to all that China is one of the HUGE manufature centers of the world. Every year tens of thousands of air compressors and compressors related parts go abroad from China. But due to the information gap and the lack of professionalism in air compressors services, most of the international buyers feel it is hard to find a reliable supplier with professional service and the most competitive prices. CPMC is growing to be China’s large online distributor offering BETTER prices than any of those compressors agents on Alibaba or Made-in-China because of the expensive commission, advertisement cost and transaction fee which is aggressively or outrageously charged by those platforms due to their namely high traffic. However our own networks enable us to provide the best prices and products to our customers. Learn more about Chengdu Air Compressors Dealer.
ZR90 Atlas Copco Year 2005, Serial No AIF 077 453 onward, suitable for ZR55, ZR75,…
2657568487 Epiroc VALVE, RELIEF 2657570780 Epiroc BUSHING, IND 2657572398 Epiroc GEAR 2657572406 Epiroc GEAR 2657580516…
2205406514,2205406521改2205490414阿特拉斯富达油分3002600172 New PN 1625005590 Atlas Copco空压机配件油分 2205178526改2205269477阿特拉斯博莱特空压机油气分离器1625481150 New PN 1625481151 Atlas Copco空压机配件油分 2911011703改3002608710阿特拉斯移动空压机配件油分包2903035100 New PN…
1621700002 Core Cooler 1621-7000-02 Atlas Copco 冷却器全新正品 中国供应商价格 1621700008 Core Cooler 1621-7000-08 Atlas Copco 冷却器全新正品…
523 Epiroc Spare Parts 15412298 SHAFT to 3128303569 SUPPORT Mini Catalog
DIAMEC 232 Spare Part Recommendations Ref. Description Part Quantity for Comment No. Number 1 Year…
This website uses cookies.